縮圖- TOSHIBA.JPG  Toshiba 32G FlashAire W04 U3 C10 SD Card 
  有時候拍個二張 十張照片,就要拔插USB線,或SD卡滿麻煩的。  

  查資料無線傳輸記憶卡最多人用的是EYE FI,還有TOSHIBA的。

  跑了四五家,發現價差還滿大的。

 
 試了三天才連線成功,失敗主因是我無線網卡沒安裝好,

 所以電腦的WIFI是失敗的,當然SD卡也無法跑WIFI。

  心得 :1.拍幾照張片而以,用SD卡很方便,只需開啟相機電源,等個幾十秒,電腦抓到相機後,點選相機的WIFI連線(如同手機連WIFI意思),
再開啟FLASHAIR資料夾就能傳輸。

 2.要傳幾十幾百mb,就不要用這卡了,會很慢。

3.可以減少USB線,SD卡拔插,也就避免插孔損壞要維修,我以前的e410修過cf卡槽,約一千元。

維修的一千元,不如拿去買WIFI卡(速度提升了)。

安裝方法:1.下載驅動程式,GOOLE打 toshiba flashair,記得看您是 W03或W04

1.jpg

2.電腦要先設定好WIFI,還要安裝無線網卡,

到螢幕右下角能出現WIFI點,之後相機才能找到WIFI,如同手機WIFI意思。

下面有 USB無線網卡安裝教學。

2.jpg

3.安裝TOSHIBA SD卡的驅動程式:

一.點選之前下載的檔案,並完成安裝。

二.把SD卡插入電腦讀卡機。

3.jpg

4.執行FLASHAIR TOOL(工具設定):(寫錯了它不是驅動)

一.點選(網路設定)

輸入SSID及密碼,以後相機的WIFI名稱,可以自行設定

41.jpg

42.jpg

43.jpg

4.執行FLASHAIR TOOL(工具設定)
一.網路設定
   輸入電腦無繳網卡的WIFI帳號密碼(之前就設定好了)

44.jpg

4.執行FLASHAIR TOOL(工具設定)
 三.點選(FLAHSAIR驅動器)會產生連結資料(flashair),之後傳輸檔案要用的

45.jpg

46.jpg

SD卡從電腦的讀卡機拿出,插到相機後,開機

47.jpg

6.開啟相機
再執行產生的TOSHIBA FLASHAIR資料奏.就能無線傳輸

51.jpg

52.jpg

53.jpg

Sometimes taking two pictures of ten, it is necessary to insert and remove the USB cable, or the SD card is full of trouble.
Check the data wireless transmission memory card most people use is EYE FI, there are TOSHIBA's
After four or five homes, they found that the spread was still full.

Tried three days before the connection was successful. The main reason for the failure was that my wireless network card was not installed.

So the computer's WIFI is a failure, of course, SD card can not run WIFI.

Experience: 1. Take a few photos and use a SD card is very convenient, just turn on the camera power,

Wait a few seconds a minute, after the computer captures the camera WIFI, then open the FLASHAIR folder will be able to transmit.

2. To pass several hundred mb, do not use this card, it will be very slow.

3 can reduce the USB cable, SD card plug, also avoid jack damage to repair, my previous e410 repaired cf card slot, about one thousand dollars

installation method:
1. Download the driver, GOOLE hit toshiba flashair, remember to see if you are W03 or W04

2. The computer must first set up WIFI, but also install a wireless network card.

In the lower right corner of the screen, a WIFI point can appear. After that, the camera can find the WIFI, just as the mobile phone WIFI means.

The following USB wireless network card installation teaching.

3. Install the TOSHIBA SD card driver:

one. Click on the previously downloaded file and complete the installation.

two. Insert the SD card into the computer card reader.

4 implementation of FLASHAIR TOOL (tool settings): (wrong it is not a driver)

One. Click (Network Settings)

Enter SSID and password. The camera's WIFI name can be set later

4. Execute FLASHAIR TOOL (tool setting)

One. Network settings

Enter the WIFI account password for the computer without a network card (previously 

4. Execute FLASHAIR TOOL (tool setting)

three. Click (FLAHSAIR driver) will generate link data (flashair), then use the file to transfer

The SD card is taken out from the computer's card reader, inserted into the camera, and turned on

6.Open perform the TOSHIBA FLASHAIR data.Can wirelessly transmit

 

arrow
arrow

    賴小彬 發表在 痞客邦 留言(0) 人氣()